Ian Daly
-
Posts
58 -
Joined
-
Last visited
-
Days Won
3
Content Type
Profiles
Forums
Calendar
Posts posted by Ian Daly
-
-
I'm having a bit of luck with marketplace atm so it'll go on there, will take it down to my friendly mot tester in the morning with crossed fingers, I'm pretty confident it'll pass🙏🤞🙏🤞
-
So I done the calculations and with the help of tier4 ism, I reckon (due to my circumstances) I'd clear £300 ish on doing Coldplay up, frankly not worth my while. I haven't the time to sell her 'normally' so if anyone here can can come and get her before Wednesday. £150 mot is due 08/01/21 she is taxed to 31/12/20 though that's immaterial, she starts and runs well, clutch is heavy, that said Jools says it's not a problem (all 8.5 stone of her), any interest/question ring me 07941879598
-
Cheers mk2, hoped you'd give your thoughts, unfortunately I haven't time to work on it have shedloads of things to get done before we return to France next Wednesday, I will (assuming I can) get it mot'd🤔, but clutch is a bit too big a job with the resources I have left here 😕... Ta
Ian
-
Hi all
So the permenant move to France has happened, Coldplay is now no longer needed. 2000 1.7 sdi roughly 130k pretty rough state but minimal an only superficial rust on roof only, clutch needs renewal and I reckon she needs timing belt. I'm only the 2nd owner, unfortunately she ain't the £30 tax kinda girl 😕. Thoughts, questions, interest?
Situated in Kingston upon Thames. I'll post some photos later.
Ian
-
I have no idea, it strikes me that ALL the spades on the rear are interconnected! No, I'm not kidding. Weirdest switch I have ever seen 🤪
Ian
-
Ah, I hadn't realised, it's a switch, it's a switch that seem very difficult to get hold of, I'd assume run of the mill stuff like that was easily available fro EuroCar parts, no it had to come (eventually) from Germany.
Took the old and knackered on apart, the sprung contact(?) fell out, can't be arsed to figure out where it came from but the of white base on the half to the right hand side is showing some serious wear, dunno, 'electricks' aren't my forte!
Ian
-
1
-
-
Topran? Is that the manufacturer of the linked puller set?
Ian
-
8 minutes ago, Silver! said:
Split the how to and saved I the Archive and How to guides.
Thank you Silver, never thought one of my post would make it to such heady heights 😎
Ian
-
2
-
-
Rich, why drill out the barrel when there was nothing wrong with it, moreover you still wouldn't be able to access the fixing bolt and as mk2 says, I keep the existing key/immobiliser.
Mk2, the only part I needed in the end was the actual switch unit, the bit behind the key turn (see pic). The sleeve was a pain, the lip is 2mm at best so your average puller is useless, the use of mole grips is not recommended by me but it saved me from taking a 'kin great big hammer to the thing! The spring, your guess is as good as mine but I suppose it ensures the load through the steering column is constant (ish). I haven't taken the switch apart, thought I'd do it better following several beers and a decent nights rest😁
Ian
-
Finally done it!😁😎
The procedure didn't start too well, could I get the steering wheel off, yes but after nearly an hour! My problem was the centre boss with the air bag would not come away, I'd love to tell you about some magical way that I finally discovered, but there wasn't one, just plain old perseverance and a load of swearing. Wheel outer came off easily to reveal this (1st photo, sorry I've forgotten how to insert pics)
Next round of swearing! I had to buy a new three legged puller ready for this, it refused to work, the toes were too rounded to get enough purchase upon the collar, the lip can't be 2mm deep, I tried all sorts to get it to work but it wasn't having it. In the end I resorted to using a 4" pair of mole grips (rounded jaws) wound as tight as possible onto the collar behind the lip and the using the puller with just two legs. I think I got lucky here and off the collar came (pics 2 &3).
I removed the interference fit screw, same 4" mole grips, and with a good bit of wiggling the barrel came off (pic4) this revealed the fixing for the switch (pic5). It may well be that it might just be possible to undo that bolt (note: it is a small cross-headed bold and not a screw) from behind, you can see a channel in the barrel casting leading to the bolt, it's a hindsight thing and frankly I'm not convinced it'll work as I seem to remember that it's in at a bit of an angle.
Anyway that's it, I put the new switch in, refitted the barrel, replaced a minimum of wires, reconnected the battery and she fire up first ask!
Hope this is of use to someone?
I'll rename this thread to 'fitting new ignition, switch 2000 Lupo' if I can if not can I get an admin to do it for me please?
Any question please don't hesitate to ask, unless you're going to ask me to do it for you, then please hesitate at length!
Ian
-
2
-
-
Will do, hopefully tomorrow, had to buy a hub-puller (arriving today) as I cannot find my old one anywhere ☹️
Ian
-
Looks like an epidemic then , oh hell, not another ☹️
Ian
-
On 8/21/2020 at 2:25 PM, Sarahs Lupo said:
"so been 10 days and havent had any issues so far!....."
Flash git!!!!
Ian
-
Hi all
Update (ish) Mk2, had I the time I was going to go down the route of a sneaky on/off switch, but I didn't think I would have the time, I ordered the new part from Autodoc, turns out they're in Germany, use an appalling delivery company , expensive and slow, so I did have the time, had I known!
Also as quoted by Sarahs Lupo, no it's not possible to remove it from behind, at least on mine, as the only fixing is only accessible once you've remover the barrel!
Unit arrived yesterday afternoon 1st Sept, ordered 24th Aug, now, where did I put my hub puller?
Oh, BTW when this first occurred turning the ignition did absolutely nothing, no idiot lights, radio fan anything, last time I turned the key, whilst looking for the rearward removal, position 1 did become available, so I suspect something loose in the actual switch, Bah!
Cheers
Ian
-
OK so tried and tried all to no avail, have just found this https://www.youtube.com/watch?v=EuY84R8h1hc , it shows why the fixing for the switch is hidden by the steering column, so it aint coming out intil I spring the whole lock piece 😩
Cheers
Ian
-
This it https://www.buycarparts.co.uk/automega/9011722?
It's just that on the video mentioned above it shows only the back half of this unit being removed 🤷♂️
Ian
-
OK so it wasn't the 109, new one purchased and fitted, no change, BAH!
So I'm pretty sure it is the actual switch, saw a youtube vid (https://www.youtube/watch?v=1z6RJetRM28) showing how the switch can be removed from the back , as suggested by mk2 👍, so I'll be giving that a go now it's cooled. Anyone know the part number or where I can find it or even how to describe it properly?
ALL advice massively appreciated!
Ian
-
Is there nothing you won't do to your Lupo? 😎
Ian
-
I figured out it was 109 but thanks for the support 👍 and excellent advice.
Tapped it, wiggled it, slapped it about a bit, nah, nothing, it just won't play ball, it's out and I'm just off to see if I can get a replacement now, have ordered one from Euro Car Parts but can't collect that until tomorrow, never mind if it is that and I can get another it's a spare, maybe the replacement won't last 20 years eh? Of course if it is the switch, no end of replacement relays will help ☹️. I'll have look to see itf it'll come out from the wire end, well I will if it cools down a bit 🥵 If it does need drilling out it won't me Mr Ham-Fists here doing it!
Ian
-
OK, so my tame mechanic seems to be dragging his feet and hasn't pick Coldplay up, thought I'd have another look, I can do nothing with the ignition because of the non-interference fittings, of course I could have an attempt at drilling them out but I just know where that would end up. The relays though, I can get to them and with a great deal of sweat (it's already 32 degrees here) I could change them, so which one? I have four, looking at them right to left, 405, 100 and 109 with 103 on a different line above?
Ian
-
Hi,
I did one with a 'vacuum pump', tube goes down the dip stick guide, from memory it was pretty successful, I think I got 85-90% out of the sump, cant see it working too well with the gearbox as you won't have a direct route to the bottom of the unit?
Ian
-
1
-
-
I failed miserably, falling at the first fence, I took off the steering column cowl, the parcel shelf beneath the wheel and unbolted the fuse box, I then looked at removing the ignition switch, no go, interference fittings and no obvious way of getting them off, I've now booked it in to have it done, I'll let you all know what was what.
Ian
-
Hi Mk2, thanks for coming back to me, you are correct, of course it can be resuscitated 😁 it's a right pain searching for the bits, think I'll get the old bits out and use their numbers, will I run into difficulties with the key coding or is that resolved within a different unit?
Of course I'll let you all know how it goes 👍
Ian
-
Hi Skezza, thanks for the reply, no, I've done nothing so far she needed to get in to open up the office and as I said she taken the damn keys with her. I doubt it's the battery though, the dash lights didn't even glow dimly and the battery was new this time last year, all tight, I did get chance to check that. Gut feeling says that there's a problem with the switch and it's subsequently blown a fuse.
Ian
Lupo sdi, what's it worth?
in Volkswagen Lupo
Posted
I ought to point out that there's probably nothing really wrong with the clutch, Jools manages, all 8.5 stone of her, it's just that I've got used to the easy to drive Passat. Assuming she passes the mot in the morning the price will rise to £350..just taken these, the tape is a bit OTT, just to stop the broken valance flapping, anyway I've got some yellow tape now 🤣🤣🤣