Search the Community
Showing results for tags 'wire'.
Found 4 results
Sorry for the long post as well it's a lot to read Okay so to start of this is my first time ever installing something like this in a car, I followed the instructions that come with the kit however when I fitted my new active subwoofer in my car I thought all had gone well it turned on and played music through it, however the subwoofer does not turn off when I remove the key from the car. I have googled this and it said something about the remote turn on wire which for me is on the back of the head unit and is a blue and white wire. The cable that come with the subwoofer is blue not that it matters as its a remote turn on wire for the sub but I ran this wire through the car to the head unit and then I have wired the blue wire with the kit to the remote wire on the back of the head unit which was the blue and white one.....I did this by simply cutting the wire in half and then joining them together with the blue wire from the subwoofer creating a "T" junction effect. I have not got a photo of this part however in the images you can see that I have had to tape up the blue and white again while I try and find a solution haha Note:I had wired this all up before turning the sub on for the first time I didn't add the remote wire after. Sorry for the amount of detail but really not sure on what the problem could be I can have links to photos if it helps as well. Thanks to anyone who can help me Active subwoofer: Edge EDB12A 2014 model Car: VW Lupo W reg (2000) Head unit: jvc kw-xr811 http://www.manualslib.com/manual/488544/Jvc-Kw-Xr811.html?page=2#manual (Wiring/ install manual for help.) Okay so I had a second look today at this issue and I was thinking if it was possible to wire it in with the yellow wire from the iso harness as this gets 12v when the ignition is on and then goes off when the key is removed? If this is even right? this is what I mean: https://i.imgur.com/nBpyd5q.jpg I have some photos to show how the ISO harness is done I had to change the yellow and the red wires around as the Unit was not remembering anything when I turned the car off so that's why. When I first tried this by linking it up with the yellow 12v wire it made the car ignition go backwards the stereo would only come on once the car had gone from ignition to off it would not come on otherwise even if the car was started so not sure on that. I also am not sure how to show images so I have had to post links to them as well https://imgur.com/a/N8lss
Hi all, sorry to be one of those "first post is a question" types but any input would be appreciated. Having recently bought a 1l Lupo E (1999) I've just fitted a new stereo and behind the Din slots there was another connector not plugged into anything that looks like it comes from the same loom as the hazard lights switch (just below the din slots). It is separate from the ISO blocks but is a plastic connector with 2 pins, the wires leading up to the connector are brown and blue/grey. I'll try and get a picture tomorrow but does anyone have any idea what it could be ? Cheers, Tomm
Hey guys I recently lowered my cars on TA Technix coilovers and after having them for two days they have already started chewing through tyres. I think it might be because of the profile on my tyres which are 65, but not sure is the strut was put on properly. So I may end up buying new wheels and lower profile tyres. Thanks Ben
Thought i'd just whap up a quick piccy of what im planning on fitting in the car when i finally get the time: Sundown SAZ-1500d amp Valeo 108a Passat alternator Focal PS-165 Component speakers KnuKonceptz 0AWG cable Stinger 14AWG Speaker wire 5L Fiberglass kit 5L Contact adhesive Paint + lacquer kit Already fitted: Alpine CDE-135BT Head unit XS Power D1200 AGM Battery 'The Big 3' Upgrade with black KnuKonceptz 0AWG I've probably missed out something but i've still got plenty left to buy