mukilupo

How low do they go at the back?Thanks.

Looks great.

Remove center heater dial which controls fan speed. Pull of using bull nose pliers wrapped in cloth. should see One bulb, pull out gently. Vw 1777512/12v 1.2w from vw or any car shop , hope this helps.

Try putting in key in boot lock. turn key to lock, then use remote key lock/unlock.

Hi, pollen filter as above ,just take care when you replace cover as its a tight fit or it may split the pastic.As for Air filter ,lift engine cover from front and gently pull towards you again take as the rear two rear brackets are easily broken, then remove 6/7 screws to get to the air filter. Good luck.

Mine are on 40mm Apex springs, looking at coilovers as mentioned above dont want change twice.

Looking good, what coilovers are you using and are they any good?PS nice Garage.

Hi, The rear's were done using existing gti bases having all the orignal covers removed and replacing with new near matching black cloth.The only thing used from Mk4 rear bench were the blue inserts. Thanks.

Thanks for the replies, i think they will fit all Lupo's might have to use GTi front bases to make work properly to get seat moving forward,back and tilt.Got rears done by HRS in Broxbourne, the only thing he could salvage from the rear bench were the blue inserts the rest of the cloth was supplied and fitted by them. As for the seats i was going to go for something different but at the end i went for the factory look. Thanks.

HI, after much deliberation I have just fitted mk4 Recaro's using gti front seat bases, well worth the effort . Go for it. Thanks. PS thanks to Henlupo for helping me fit them and Mike M for his advice.

Hi, how much was the stalk, was it OEM?Did you disconnect the battarie and when you finished and connected the batterie did the air bag light go out. Thanks.

Spot on Mike, looking for a cheap sollution.Thanks.

Hi, got door cards in grey can they be sprayed Black or Will they get damaged etc? Thanks.

Try something called {Bar keepers friend} stanless cleaner with some fine Wet/Dry paper.Good luck.

Thanks for all the replies, is it easy to fit new switch/ stalk? Thanks

Hi, not sure how to explane but here goes, when turning Right you push the indicator stalk half way up , but not till it fully clicks there is fast clicking sound as if , one of the bulb is not working ,at this point the right indicator does not work then push fully up and indicator works perfect.The left indicator work perfect in both possition's.Any ideas?Thanks for looking.

Hi , looking for KW -V1 coilovers for my Lupo gti, where is the cheapest? Many thanks.

Hi, does Cobra DAYTONA fit Lupo any problem's at the widest point etc... Many thanks.

Hi,More than 10mm always use hubcentric,price around £40/60.00.Try Venommotorsport,{ask him all questions on bolts etc}go for quality like H&R or Eibach. ET is probably 25,30 or35 .Hope this helps.PS you may also need New longer bolts for wheel locks.

Hi,More than 10mm always use hubcentric,price around £40/60.00.Try Venommotorsport,{ask him all questions on bolts etc}go for quality like H&R or Eibach. ET is probably 25 or 28.Hope this helps.

Saw car at the show, Top job as usual would not expect anything less.Sorry to say BBS for me ,its so Gti.

Hi, want to fit MOMO steering wheel{No Airbag}, is it a DIY job removing standard Gti wheel with Airbag. Many thanks.

Remove center dial that controls fan speed.Pull of using pliers wrapped in cloth, should see ONE bulb behind pull out gently. Vw No177512/ 12v 1.2w,or go to Halfords etc.

Hi, as mentioned above, i changed the bulb this morning using B N pliers took few minutes, just take your time.Bulb from VW N0177512 {12v 1.2w} or just go to Halfords.Hope this helps.

Hi, i thought if you clean the TB you have to reset the engine by Vw mechanics?